sks-15/CF/A

IO-Link
Bild vom sks Ultraschallsensor
  • 1 x Push-Pull 1 x Push-Pull
  • 250 mm 250 mm
20 - 250 mm
прямоугольный
IO-Link
бесконтактный выключатель / отражающий режим оконный режим отражающий барьер
kleinste quaderförmige Bauform
schlankes Schallfeld
IO-Link
Smart Sensor Profile
UL Listed

Ультразвуковых конкретных

Распростронение отраженного сигнала по времени задержки
380 kHz
20 mm
150 mm
250 mm
0.10 мм
± 0.15 %
± 1 % (температурный дрейф внутренней компенсации)

Электрические данные

10 - 30 VDC, защита от обратной полярности
± 10 %
≤ 30 mA
4-контактным разъемом M8

Выходы

релейный выход
Push-Pull, UB-3 V, -UB+3 V,Imax = 100 mA
2,0 мм
25 Hz
32 ms
< 300 ms

Входы

Управляющий вход

Корпус

ABS
полиуретановой пены, эпоксидной смолы с содержанием стекла
IP 67
-25 ° C до +70 ° C
-40 ° C до +85 ° C
8 g

Технические характеристики/характеристики

да
1 кнопка
Teach-in via push-button
IO-Link
нет
нет
1 х зеленый светодиод: рабочий, 1 х желтый светодиод: состояние реле
kleinste quaderförmige Bauform
schlankes Schallfeld
IO-Link
Smart Sensor Profile
UL Listed

IO-Link

sks-15/CF/A
13009
да
COM2 (38,4 kBaud)
8 ms
32 Bit PDI
Bit 0: initial state Pin 4; Bit 8-15: scale (Int. 8); Bit 16-31: measured value (Int. 16)
Identification, switched output, filter, temperature compensation, operation
SP1 Teach-in, SP2 Teach-in, factory settings
да
IODD версии 1.1

Аксессуары

KST4A-2/M8
KST4A-5/M8
KST4G-2/M8
KST4G-5/M8
SoundPipe sks1

Подходящие датчики

prev
next
Details zu KST4A-2/M8
KST4A-2/M8

KST4A-2/M8

cable, 4 contacts, female angled connector M8, cable length 2 m
Details zu KST4A-5/M8
KST4A-5/M8

KST4A-5/M8

cable, 4 contacts, female angled connector M8, cable length 5 m
Details zu KST4G-2/M8
KST4G-2/M8

KST4G-2/M8

cable, 4 contacts, female cable connector M8, cable length 2 m
Details zu KST4G-5/M8
KST4G-5/M8

KST4G-5/M8

cable, 4 contacts, female cable connector M8, cable length 5 m
Details zu SoundPipe sks1
SoundPipe sks1

SoundPipe sks1

SoundPipe for sks ultrasonic sensors. SoundPipe sks1 intensively bundles the sound field and allows measurements in drill holes and openings with small diameters. Push the SoundPipe down on the transducer until it is flush with the sensor housing. Avoid axial tensile force on the SoundPipe, otherwise the SoundPipe may dismantle from the sks sensor.

recently viewed

prev
next