The lcs+ ultrasonic sensors
have a block-like plastic housing with a base area of only 62 x 62 mm and four fastening bores.
The sensors are Listed to applicable UL Standards and requirements by UL for Canada and the US.
lcs+
新しいlcs+超音波センサーは非常にコンパクトで正方形の筐体 - アナログまたはスイッチング出力+IO-Linkを備えております。
検知範囲
3.4 m
6.0 m
出力
Cuboidal:
特徴
- Very compact housing dimensions only 62 mm x 62 mm x 37.2 mm
- IOリンクインターフェース 新しい工業標準をサポート
- スマートセンサポートフォリオ IO-Linkデバイス間の透明性の向上
- Synchronisation and multiplex mode for simultaneous operation of up to ten sensors in close quarters
- 8 m maximum detection range
- カナダと米国のUL安全規格に準拠
基本情報
- 1 Push-Pull switching output, or 2 pnp switching outputs
- 4-20 mA 0-10 V アナログ出力 一つのセンサーにつき、二つの出力シグナル
- T1、T2ボタンによるマイクロソニック・ティーチイン
- 0.18 mmから2.4 mmの分解能
- 温度補償
- 9から30 Vの動作電圧 V
- リンクコントロールPCからセンサーの設定
Sensor matrix
The sensor matrix gives an overview of standard sensors from lcs+ family. Make your choice based on operating range and available outputs and click in the matrix.
3.4 メートル6.0 メートル
1 Schaltausgang IO-Link
2 Schaltausgaenge
1 Analogausgang
1 Schaltausgang IO-Link
1 Analogausgang
Two dual colour LEDs
show all operating statuses.
Using the two Teach-in buttons T1 and T2
the lcs+ sensors can be easily set (Teach-in).
Three output stages are available for selection:
1 Push-Pull switching output with pnp or npn switching technology with IO-Link interface
2 pnp switching outputs
1 analogue output 4–20 mA or 0–10 Vスイッチ出力を備えたセンサーのもつ3つの動作モード:
- 単一スイッチングポイント
- 双方向反射バリア
- ウィンドウ・モード
Teach-in of a single switching point
- Place object to be detected (1) at the desired distance
- Push button T2 for about 3 seconds
- Then push button T2 again for about 1 second
Teach-in of a two-way reflective barrier
with a fixed mounted reflector
- Push button T1 for about 3 seconds
- Then push button T1 again for about 10 seconds
For setting the analogue output
- Initially position the object to be detected to the sensor-close window limit (1)
- Push button T1 for about 3 seconds
- Then move the object to the sensor-distant window limit (2)
- Then push button T1 again for about 1 second
For configuration of a window
with two switching points on a single switched output, the procedure is the same as setting the analogue.
Easy to synchronise
If several lcs+ ultrasonic sensors are operated in one application, the can be synchronised via pin 5 to prevent.
If more than 10 sensors must be synchronised, this can be carried out with the SyncBox1 , which is available as an accessory. Synchronisation via pin 5 is also possible in IO-Link mode.
Analogue sensors
check the connected working resistance at the output and automatically switch to 4–20 mA current output or 0–10 V voltage output.
NCC/NOC
上昇エッジ、下降エッジを5番ピンで設定する事が可能です。
LinkControl
permits comprehensive parameterisation of lcs+ ultrasonic sensors via the LinkControl adapter LCA-2 which connects the sensors to the PC.
IO-Link
Ultrasonic sensors lcs+340/F/A and lcs+600/F/A have a Push-Pull switching output and support IO-Link in version 1.1 as well as the Smart Sensor profile.
