The lcs+ ultrasonic sensors
have a block-like plastic housing with a base area of only 62 x 62 mm and four fastening bores.
The sensors are Listed to applicable UL Standards and requirements by UL for Canada and the US.
lcs+
The lcs+ ultrasonic sensors come in a very compact square-shaped housing - with analogue or switching output + IO-Link.
Detection ranges:
3.4 m
6.0 m
Outputs:
Cuboidal:
Highlights
- Very compact housing dimensions only 62 mm x 62 mm x 37.2 mm
- IO-Link interfacefor support of the new industry standard
- Smart Sensor Profiles more transparency between IO-Link Devices
- Synchronisation and multiplex mode for simultaneous operation of up to ten sensors in close quarters
- 8 m maximum detection range
- UL Listed to Canadian and US safety standards
Basics
- 1 Push-Pull switching output, or 2 pnp switching outputs
- Analogue output 4–20 mA and 0–10 V with automatic switching between current and voltage outputs
- microsonic Teach-in by using button T1 and T2
- 0.18 mm to 2.4 mm resolution
- Temperature compensation
- 9–30 V operating voltage
- LinkControlfor configuration of sensors from a PC
Sensor matrix
The sensor matrix gives an overview of standard sensors from lcs+ family. Make your choice based on operating range and available outputs and click in the matrix.
3.4 m6.0 m
1 Schaltausgang IO-Link
2 Schaltausgaenge
1 Analogausgang
1 Schaltausgang IO-Link
1 Analogausgang
Two dual colour LEDs
show all operating statuses.
Using the two Teach-in buttons T1 and T2
the lcs+ sensors can be easily set (Teach-in).
Three output stages are available for selection:
1 Push-Pull switching output with pnp or npn switching technology with IO-Link interface
2 pnp switching outputs
1 analogue output 4–20 mA or 0–10 VThe Ics+ sensors with switching output have three operating modes:
- Single switching point
- Two-way reflective barrier
- Window mode
Teach-in of a single switching point
- Place object to be detected (1) at the desired distance
- Push button T2 for about 3 seconds
- Then push button T2 again for about 1 second
Teach-in of a two-way reflective barrier
with a fixed mounted reflector
- Push button T1 for about 3 seconds
- Then push button T1 again for about 10 seconds
For setting the analogue output
- Initially position the object to be detected to the sensor-close window limit (1)
- Push button T1 for about 3 seconds
- Then move the object to the sensor-distant window limit (2)
- Then push button T1 again for about 1 second
For configuration of a window
with two switching points on a single switched output, the procedure is the same as setting the analogue.
Easy to synchronise
If several lcs+ ultrasonic sensors are operated in one application, the can be synchronised via pin 5 to prevent.
If more than 10 sensors must be synchronised, this can be carried out with the SyncBox1 , which is available as an accessory. Synchronisation via pin 5 is also possible in IO-Link mode.
Analogue sensors
check the connected working resistance at the output and automatically switch to 4–20 mA current output or 0–10 V voltage output.
NCC/NOC
and rising/falling analogue characteristics can also be set via the buttons.
LinkControl
permits comprehensive parameterisation of lcs+ ultrasonic sensors via the LinkControl adapter LCA-2 which connects the sensors to the PC.
IO-Link
Ultrasonic sensors lcs+340/F/A and lcs+600/F/A have a Push-Pull switching output and support IO-Link in version 1.1 as well as the Smart Sensor profile.
You have special requirements?
Nothing as simple as that.
With us, you can easily find an individual solution. Let us talk about your application: +49 231 97 51 51-82.
