With a housing length of only 55 mm
nano sensors with switching outputs are the smallest ultrasonic sensors inside the M12 threaded sleeve on the market. Analogue sensors are 60 mm long. nano has a 4-pole M12 circular plug and are taught via pin 2.
nano
nano – what‘s in a name? At just 55 mm long, including plug, the nano is the shortest M12 ultrasonic sensor on the market.
Detection ranges:
0.15 m
0.24 m
Outputs:
Threaded sleeve:
Highlights
- Ultrasonic sensor in the M12 threaded sleeve
- The total length including plug is only 55 mm
- IO-Link interfacefor support of the new industry standard
- Smart Sensor Profile more transparency between IO-Link Devices
- Improved temperature compensation adjustment to working conditions within 45 seconds
- UL Listed to Canadian and US safety standards
Basics
- 1 Push-Pull switching output pnp or npn basis
- Analogue output 4–20 mA or 0–10 V
- 2 detection ranges with a measurement range of 20 mm to 350 mm
- microsonic Teach-in on pin 2
- 0.069 mm resolution
- Operating voltage 10–30 V for use with various voltage networks
sensor matrix
The sensor matrix provides an overview of the standard range of the nano sensor family. Select the desired operating range and available outputs by clicking on the matrix.
0.15 m0.24 m
1 Schaltausgang IO-Link
1 Analogausgang
1 Schaltausgang IO-Link
1 Analogausgang
The temperature compensation
of the sensors profits from a significant improvement. The sensors reach their operating point only 45 seconds after activation of the operating voltage. We now compensate for the influence of self-heating and installation conditions. This brings improved precision shortly after activation of the supply voltage and in running operation.
For the nano sensor family
there are 2 output stages and 2 measuring ranges available:
1 Push-Pull-switching output, in pnp or npn circuitry with IO-Link interface
1 analogue output 4–20 mA or 0–10 VWith the internal alignment assistance
the sensors with Push-Pull switching output can be optimally aligned to the object during installation.
The nano sensors with switched output have three operating modes:
- Single switching point
- Two-way reflective barrier
- Window mode
Teach-in of a single switching point
- Place object (1) to be detected at the desired distance.
- Apply +UB to pin 2 for about 3 seconds.
- Then apply +UB to pin 2 again for about 1 second.
Teach-in of a two-way reflective barrier
with a fixed mounted reflector.
- Apply +UB to pin 2 for about 3 seconds.
- Then apply +UB to pin 2 again for about 10 second.
To set a window with two switching points
- Place object to the sensor-close window limit (1).
- Apply +UB to pin 2 for about 3 seconds until both LEDs flash.
- Then move the object to the sensor-distant window limit (2).
- Then apply +UB to pin 2 again for about 1 second.
For setting an analogue output
- initially position the object to be detected on the sensor-close window limit (1).
- Apply +UB to pin 2 for about 3 seconds until both LEDs flash.
- Move the object to the sensor-distant window limit (2).
- Then apply +UB to pin 2 again for about 1 second.
NCC/NOC
and rising/falling analoge characteristic can also be set via pin 2.
One green and one yellow LED
indicate the state of the output and support microsonic Teach-in.
IO-Link integrated
in version 1.1.2 for sensors with Push-Pull output. The nano-15/CF and nano-24/CF support the Smart Sensor Profile, which creates more transparency between IO-Link devices.
You have special requirements?
Nothing as simple as that.
With us, you can easily find an individual solution. Let us talk about your application: +49 231 97 51 51-82.
